shopping cart
Item Qty Price

Sub Ttl:  £0.00
Delivery:  £0.00
Tax:  £0.00
Total:  £0.00

categories
COUPLING SPARES + FRICTION PADS
DAMPERS
JOCKEY WHEELS + CLAMPS
TRAILER BRAKES + BRAKE PARTS
WHEEL BEARINGS + HUB CAPS
WHEEL STUDS / NUTS + WHEEL BOLTS
    TRAILER MUDGUARDS
      TYRES + WHEELS
      TRAILER LIGHTS
      TRAILER ELECTRICS
        SECURITY
          BOAT ROLLERS
            TOWBALLS+PLATES
              LUBRICANTS AND COATINGS
                TRAILER FITTINGS
                RATCHET STRAPS
                  SUSPENSION + UNDERGEAR
                    U BOLTS

                      select currency

                      PLEASE NOTE PRICES QUOTED IN OTHER CURRENCIES ARE A GUIDE ONLY 

                      All prices inc VAT @20%

                      P+P is calculated by weight

                                  We can make           
                             NUMBER PLATES      
                             For only £8 each        
                                                                  
                            Plates supplied are      
                                520mm x 111mm     
                       and can be made on site
                              while  you wait.       


                      We can only supply number plates in person and will need to see your documents. See the link below for requirements


                      https://www.gov.uk/displaying-number-plates/getting-number-plates-made-up
                       
                      You are here: Home > WHEEL BEARINGS + HUB CAPS > WHEEL BEARINGS AND KITS > BALL RACE AND UNITIZED BEARING KITS
                        Our Price: £0.00

                      INSTRUCTIONS FOR REMOVING & FITTING EURO BEARINGS

                       Instructions for Removing & Fitting Euro Bearings
                       
                      When removing / fitting Euro bearings, it is extremely important that you work carefully and keep everything clean in order to ensure efficient operation and to maintain safety.
                       
                      To ensure that the bearings operate properly it is essential that the correct tools and methods are used to fit them.
                       
                      Installation should be carried out under clean conditions. Do not unwrap bearings until you are ready to fit them.
                       
                      Removal
                       
                      1) Place chocks under at least one wheel of the vehicle
                      2) Loosen wheel bolts before jacking up the vehicle
                      3) Jack up the vehicle and secure on axle stands
                      4) Remove the wheel bolts and wheel
                      5) Remove the dust cap
                      6) Remove the brake drum
                      7) Lay brake drum on flat clean surface
                      8) Remove the circlip
                      9) Push out the bearing squarely using a hydraulic press and suitable mandrel, taking care not to damage the machined surfaces of the brake drum. The Euro bearing is now to be Scrapped as it is no longer fit for service
                       
                      Fitting
                       

                      1. WARNING  Keep the two inner half rings of the new bearing held together, otherwise the bearing could become damaged and not fit for use
                      2. Push the new bearing squarely all the way into the brake drum using a hydraulic press and suitable mandrel. NOTE The force must be applied only to the outer ring of the bearing, otherwise the bearing can be damaged and unfit for use
                      3. Fit the circlip, ensuring it is fully engaged in the machined groove
                      4. Fit the brake drum and a NEW flange nut and tighten to a torque of between 280 and 300 Nm
                      5. Refit the wheel and wheel bolts
                      6. Lower vehicle and tighten wheel bolts N S W E (88Nm)
                      7. Check and adjust brakes where necessary
                       
                      IMPORTANT NOTE
                       
                      Every time a bearing is replaced there is some deterioration of the fit between bearing & drum. It is therefore recommended that the bearing be replaced no more than twice.



                      « Back

                      quick search

                      WE HIRE A WIDE VARIETY OF TRAILERS, PLEASE CONTACT OUR SALES OFFICE.

                      ON 01823 350005

                      PLEASE DO NOT EMAIL FOR TRAILER HIRE





                      PLEASE NOTE;
                      WE DO NOT TAKE TRAILER HIRE BOOKINGS BY EMAIL
                      Please phone 01823 350005

                      All braked trailers are hired @
                      £36 for 1 day,
                      £60 for 2 days,
                      £72 for 3 days,
                      £84 for 4 days,
                      £93 for 5 days,
                      £100 for 6 days,
                      £102 for 7 days

                      All unbraked trailers are hired @
                      £15 for 1 day,
                      £29 for 2 days,
                      £42 for 3 days,
                      £48 for 4 days,
                      £56 for 5 days,
                      £60 for 6 days,
                      £64 for 7 days


                      Unbraked trailers are small camping trailers or motorcycle trailers.

                      TAUNTON TRAILERS 01823 350005


                      Please phone for any trailer advice or information

                      Home - Terms & Conditions - Sitemap